The distillation of china distillation equipment is introduced to you.
1. Separation and concentration:
The distilling of fermented grains was mainly to extract alcohol and aroma substances, and steam a certain amount of water, but also mixed with some trace substances, at the same time also discharged the distiller's grains composed of solid substances with high boiling point and water.
In addition, some low boiling point impurities, such as carbon dioxide, wine, hydrogen sulfide, free ammonia, etc. are discharged from the gas phase. At the same time, the separation of alcohol and flavor components also played a concentrated role.
china distillation equipment condenses the ethanol in fermented grains from 4% to 6% to 50% to 70%, and other substances are also increased in concentration, so that liquor retains the desired ethanol content and has a special aroma.
2, sterilization effect:
The characteristics of solid-state fermentation were cyclic fermentation of fermented grains, during which microorganisms in fermented grains were killed and impurities in fermented grains were eliminated, creating favorable conditions for normal fermentation in the next step.
3. Heating metamorphism:
Fermented grains of wine had a strong aroma, but after distillation, the flavors of white wine and fermented grains were completely different. There is a slight dispersion of aroma during distillation, and some substances that are not stable to heat. After heating, some of them are retained and some of them are heated to produce aroma substances.
china distillation equipment https://www.hzzjde.com/product/
Be the first person to like this.
The working principle and application characteristics of central machinery industrial dust collector
The central machinery industrial dust collector uses the reverse blower as the dust cleaning power, with the cooperation of the off-line switch valve, spray into each filter bag by room, so that the filter bag from the normal filter "expansion" state, into the "shrinkage" state, so as to shake off the dust on the surface of the filter bag. This series of dust precipitator mainly adopts 5-10 meters of large cloth bag, which is mainly used for dealing with large air volume, small area requirements, dust and dust are relatively easy to peel from the surface of the bag dust removal places. Widely used in metallurgy, mining, chemical industry, machinery, building materials, cement, refractory materials, electric power, food processing, medicine, casting and industrial boiler and other industries of dust gas purification.
I. Working principle of central machinery industrial dust collector
The filter mechanism of bag dust collector is the result of a comprehensive effect, such as gravity, inertia force, collision, electrostatic adsorption, screening and so on. When the gas containing dust and dust enters the dust collector through the air inlet, the larger dust particles will settle directly due to the increase of cross-sectional area and the decrease of wind speed. Smaller soot and dust particles are blocked by the filter bag to stay on the surface of the filter bag. The purified gas through the filter bag is discharged by the induced draft fan through the air outlet. With the continuous filtration, the dust and dust on the surface of the filter bag accumulate more and more, and the resistance of the filter bag keeps rising. When the resistance of the equipment reaches a certain limit, the dust and dust accumulated on the surface of the filter bag should be removed in time. Under the action of external force (mainly pulse compressed gas, backblowing gas, mechanical vibration, etc.), shake and backblow the filter bag to remove the dust and dust attached to the surface of the filter bag, so that the filter bag regeneration, cycle, continuous filtration, to ensure the continuous and stable operation of the equipment.
Ii. Characteristics of central machinery industrial dust collector
1. The filter wind speed is generally 0.5-1m/min, and the filter bag has a long service life.
2, dust collector using 5-10 meters long bag, so that the unit filter area required to cover a small area.
3, suitable for large flow of smoke, dust treatment.
4. Low failure rate of equipment; Simple operation, easy maintenance, low cost.
5. Three states of dust removal with room stop air and reverse air flow, good dust removal effect;
central machinery industrial dust collector https://www.kaisenfilter.com/Products
Be the first person to like this.
1. Strong current wiring
The strong current wiring of telephone socket mould for sale is actually consistent with the ordinary switch, and at the same time is a little simpler than the ordinary switch. The actual wiring method is basically distributed by the welder, the actual will not do a specific indication. There are some differences, mainly. The wiring of traditional switch mainly takes full account of the fact that some lights must be double-controlled switch or even three-controlled, so the wiring is more complex. At present, the wiring of telephone socket mould for sale does not need to consider the problem of multi-control at all, only the corresponding lighting effect wire must be connected to the matching switch cassette. In other words, thoroughly according to the single control to carry out wiring. So, how to complete the multi - control regulation? This is the second part of the signal line to solve
2. Route signal cables
In today's telephone socket mould for sale, the key of intelligence lies in the mutual control between switches, between which an Internet is formed. According to the transmission of data signals and instructions in the Internet, the goal of automatic control can be achieved. For example, the multi-control just now transmits instructions to the switch of specific wiring according to the signal line, and instructs the switch to turn on or off the lamp.
In order to make a network of switches, signal wires must be used to connect all switches to each other. Signal cables belong to weak wires. Actual operations, such as grooving and piping, must follow the wiring standards for weak current installation. In terms of the wiring of the most popular 485 communication protocol telephone socket mould for sale, the wiring is actually relatively simple, just use the signal line to connect each switch cassette can be connected, the interface is more flexible.
3. Suggestions for wiring:
(1) When distributing signal lines, it is recommended to take the home information box as the starting point, and use a single five-class twisted pair wire (or network line) to associate all the open ones
(2) The connection method of signal line is system bus (series) connection. See picture 1 for the actual connection.
(3) When the signal line is on the surface, a spare 15cm above and below is embedded on each switch box, which does not need to be straightened
(4) the actual wiring, you can choose the most inexpensive method, as long as it does not violate the system bus connection, but from the perspective of data signal stability, it is best to do not have a connection head in the dark.
2. In terms of scalability and convenience, the first method is strongly recommended, and the third method is generally applied. The signal lines are centralized in one place, which facilitates the regular inspection and solution of problems. This method is to cut the house into multiple parts, each part of the area as a line, and then centralized connection at the home information box, convenient for future smart home system upgrade.
Switch wiring, according to the corresponding wiring terminals connected to the live line and the light port line, the network line according to the same tone to match the connection.
telephone socket mould for sale https://www.tangrammould.com/Telephone-Socket-Mould.html
Be the first person to like this.
lumination led luminaires need external DC power supply. Generally, the power of 1 meter 60 beads 5050 lamp belt is roughly 11~14W, that is to say, each meter lamp belt needs to be equipped with about 15W DC power supply. The cost of construction will increase a lot, much higher than the high voltage LED strip. Therefore, from the overall cost point of view, the price of low-voltage LED lights is higher than that of high-voltage LED lights.
LED flexible lamp belt has the advantages of high luminance, soft and flexible, and can be cut according to the required length. The light source of lumination led luminaires is LED lamp bead, SMD patch type, and the carrier is flexible FPC board. That is, the flexible circuit board is mostly 8MM wide, 1M?? Below M, each FPC factory length is 0.5 meters.
Two or more strips may be welded to each other. Each reel of the production of lumination led luminaires is 5m in length and is packed with anti-static disk and anti-static bag, which is easy to carry and transport. If you look at the two lights separately, the price of LED lights is about the same, but the overall cost is different, because the high voltage LED lights are equipped with high voltage power supply, generally a power supply can take 30~ 50 meters of LED flexible light strip, relatively low cost of high voltage.
What are the causes of common LED lights not shining? The packaging protection of lumination led luminaires is not perfect, which leads to the impact damage of lamp beads in the process of transportation. The welding spot of lumination led luminaires has the phenomenon of virtual welding. The vibration during transportation causes the solder joint to fall off and the lamp belt does not light up. lumination led luminaires less soldering, welding spot off.
lumination led luminaires https://www.zliec.com/Led-Luminaire-Street-Light.html
Be the first person to like this.
How can white things appear on the disposable finger gloves vendor? Where did it come from? Today, take you to solve this mystery ~
Generally speaking, the appearance of white material, there are two main conditions, caused by different reasons. One is the white stripe, which is caused by uneven mixing of raw materials in the production process. Although it will make the gloves look ugly, it will not affect the normal use.
There is also a case of white particles, which is related to the coagulant on the hand mold, but the probability of this is relatively low. Before leaving the factory, strict sampling inspection is required, and only a certain amount of defective gloves are allowed to exist in the inspection.
disposable finger gloves vendor https://www.disposablesgloves.com/aiproduct-item-1253.html
Be the first person to like this.
introduction to the working principle of the dust collector is a filter type dust removal equipment based on the filter principle, using organic fiber or inorganic fiber filter cloth to filter out the dust in the gas.
⑴ Gravity sedimentation - When dusty gas enters the introduction to the working principle of the dust collector, the dust with large particles and a large ratio settles down under the action of gravity, which is the same as the effect of the sedimentation chamber.
(2) Thermal motion action -- light body small dust (1 micron below), with the flow of air, very close to the flow line, can bypass the fiber. But when they are hit by gas molecules in thermal motion, known as Brownian motion, they change their original direction of motion, which increases the chance that the dust will come into contact with the fibers, allowing the dust to be captured. When the filter material fiber diameter is finer, the open free rate is smaller, the capture rate is higher, so the more conducive to dust removal.
(3) The effect of inertia force - gas smooth filter material, can be around the fiber, and the larger dust particles zai under the action of inertia force, still according to the original direction of movement, then collided with the filter material and was captured.
⑷ Screening effect -- when the particle diameter of the dust is larger than the open ground between the fibers of the filter material or the gap between the dust on the filter material is large, the dust is blocked in the gas smooth expiration, which is called screening effect. When the accumulation of dust on the filter material increases, this effect is more obvious.
Introduction to the working principle of the dust collector has been widely used in various industrial parts for a long time to capture non-bonded non-fibrous industrial dust and volatiles, capturing dust particles up to 0.1 micron. However, when it is used to deal with gases containing water vapor, dew problems should be avoided. Bag type dust removal with high purification efficiency, is the capture of fine dust efficiency can also reach more than 99%, and its efficiency ratio is high.
introduction to the working principle of the dust collector Introduction to the working principle of the dust collector Dust hopper, air inlet and exhaust duct, filter chamber (middle and lower box), cleaning room, filter bag and frame (bag cage bone), manual air inlet valve, pneumatic butterfly valve, pulse clearance mechanism, etc.
Dust removal process: dusty gas from the air inlet into the central box, from the bag into the bag, dust is blocked on the surface of the filter bag, the purified air into the bag, and then from the upper part of the bag into the box, the exhaust pipe discharged.
introduction to the working principle of the dust collector https://www.kaisenfilter.com/What-is-the-principle-of-vacuum-dust-collector-and-what-are-the-components.html
Be the first person to like this.
The design of microfiber jewelry bag to protect jewelry box manufacturer is very important. Generally, high-quality product design and packaging design can better design a unified gift package that is more practical for consumption and quantitative for production in communication. A lot of product packaging is simplified, but there is a lack of creativity.
The design of microfiber jewelry bag to protect jewelry box manufacturer is based on the starting point of creativity and thinking. Generally speaking, it can be applied to product design rather than the starting point of the most practical packaging design concept. Once, Brain Platinum sold very well, which made many packaging manufacturers imitate the design of packaging, but in the end, it was not as beautiful and beautiful as the packaging they designed. As we all know, the product itself is on the one hand, and on the other hand, it is the eye-catching and promotional value of advertising design and packaging box. This is also a big shortcoming of many designs.
When talking about design in cooperation with packaging manufacturers, many businesses will rely on innovative design with unique personality, and sometimes ignore the consumption attributes. While demanding unique personality, they also demand to be different from their peers. In fact, this does not have any problems. But if they innovate only for the unique creativity, it will be a bit off the track. If it is accurate and unique to display advantages and consumption reasons, it is really innovation and creativity.
The packaging box is the most precious opportunity to communicate with consumers! Therefore, product packaging planning and design and gift box production have always been made from two levels in order to customize the production of microfiber jewelry bag to protect jewelry box manufacturer to create intelligent purchase reasons for consumers.
microfiber jewelry bag to protect jewelry box manufacturer https://www.forte-packaging.com/Jewelry-Pouch
Be the first person to like this.
In the box customization, the customization of Micropiber Jewelry Bag Producer is a very important one and the most widely used.
When customized Microfiber Jewelry Bag Producer, the first consideration we consider must be the material selection of the box and the determination of style style, and it rarely takes into account the inside of the box.
For the box, how to choose a suitable lining is actually a very important link, and its choice will directly affect the grade of the entire packaging box.
For customers, they do not understand the materials and uses of these lining. However, as a professional packaging customization company, we need to know the advantages and disadvantages of various materials lining, and recommend it to customers when appropriate. Essence Next, we will make a general introduction to the common MicroFiber Jewelry Bag Producer lining: cardboard or corrugated paper lining: Most of our common packaging boxes are paper. At the same time Unity of style. The cost of cardboard and corrugated paper is low in cost, environmentally friendly materials, and convenient processing. It is very popular with merchants. At the same time, the paper is easy to set and has good buffering performance. It can protect the entire item during transportation.
Paper lining is often used in electronic product packaging, red wine packaging, etc. EVA lining: EVA is a polyethylene foaming product, which has good elasticity, flexibility, resistance to compression and sealing. The EVA has a smooth appearance, uniform in the bubbles, soft and thick feel, and has a good buffer resistance. EVA lining can be used for groove design, or on the surface of velvet, the groove design can play a role in fixed and displayed products, and the velvet design can make the surface of the lining more soft and shiny. EVA lining is often used for precious and fragile product packaging. Sponge lining: The packaging suitable for high -end products can play a role in buffering and shock absorption. At the same time, the sponge lining also has the division of environmentally friendly sponge lining, anti -static sponge lining and fire -resistant sponge lining. Among them, anti -static sponge lining can protect the product from being damaged by electrical electricity for electronic products and chips. The cost of the sponge is low and easy to process, and it is also one of the lining materials that are very popular with merchants. Plastic lining: I believe that everyone will definitely not be unfamiliar with the lining of plastic materials. Plastic lining is often used in food packaging, such as moon cake gift packaging. Although the plastic lining is not soft or environmentally friendly, it is indeed one of the most used lining materials. Plastic inner lining stability, anti -squeeze, not easy to deform and cost cheap. When using it, it often matches the silk cloth. The silk cloth has a very good gloss, which can increase the texture of the entire gift box. The lining of different materials has different advantages. How to choose the appropriate lining material, I believe everyone has a preliminary judgment. In the process of transportation or handling, the lining can reduce the chance of commodity loss, and at the same time increase the grade of packaging.
microfiber jewelry bag producer https://www.forte-packaging.com/Microfiber-Jewelry-Packaging-Bag.html
Be the first person to like this.
The core technologies of the purchase of industrial grinding dust collector mainly involve the technologies of various professional technologies such as dust, steel structure, mechanical, electrical, instrumentation, welding, paint and other professional technologies. Good performance and stable operation.
(1) Surface filtering technology
Surface filtering technology refers to the filtering technology of the dust that cannot enter the filter material. Regardless of whether it is coarse, the filtering technology of the fine dust is deposited on the surface of the filter material. The surface filtering is achieved by a layer of a thin and porous film (2 μm micropores). This film is scattered with a lot of fine pores, which is convenient for breathability, easy to clear ash and low pressure. It has been applied to a bag dust collector on the surface of the film in foreign film. Project, but the main use of the film surface filtering material has always been a dust removal project or an improved project. In Baosteel's steel water -refined desulfurization and dust removal reconstruction project, the composite film 729 filter material is used to filter the dust layer into surface filtering technology. As a result, the filtering performance of the dust collector, reduced resistance, improved efficiency, and more stable and reliable operation. It is worth noting that the price of compound filter material is about 4 times the price of ordinary filter materials.
(2) Reducing the leakage rate technology
The leakage rate is an important indicator that reflects the overall performance of the dust collector. The leakage rate of the whole machine is small, which is not only conducive to ensuring the design air volume and energy conservation of the dust removal system, but also helps the equipment runs stable, reduces accidents, and extends life. The air leakage rate of the dust collector's body is ≤ 2 %, the valve leakage rate ≤ 1 %, stricter than similar equipment at home and abroad. 15 %, more than 20 % of individual ones.
(3) The air volume regulating valve that can monitor and verify the distribution status of the air volume
In the past, the air volume regulating valve, the entire valve was made of ordinary steel. During the use process, the valve board was easily worn, causing changes in the distribution status of the air volume in each room. The new type of air volume regulating valve is made of special wear -resistant materials. It can not only maintain the distribution of air volume in each room uniform, but also monitor the changes in the air volume of each room during use. The voltage difference meter. When testing at the empty load, the air volume distribution is evenly distributed in each room, and record the opening degree of the valve board of each room at this time and the reading of the pyramidal pressure meter. If the readings of the pyramid differential meter are different from the original base, the volume distribution of each room is uneven. You can find the reason for adjustment.
purchase of industrial grinding dust collector https://www.kaisenfilter.com/KSDM-4-0-Downdraft-Grinding-Dust-Collector.html
Be the first person to like this.
1. Look at the selection of materials
FAN Shell Mould is a commonly used product in the family, so one hundred must choose products with good materials. You can use the combustion test method to identify. Good quality products are not flamboyant and good flame retardant. It also produces a pungent odor.
2. Look at the feel
Good quality switches are mounted with light, good elasticity, and strong switching; switch spring with poor quality is soft, which will be stuck in the middle and easy to break. There are protective doors of the socket jack, which cannot be inserted with one foot, and a certain amount of intensity is needed.
3. Look at the appearance
Generally, the surface of the good switch is very smooth and smooth, and the imported PC materials are used, and the feel is very good. The quality of the product with poor quality is rough and the flame retardant is prone to hidden dangers of fire.
4. Look at the weight
When buying a switch, you can also take the amount of the switch. Usually the well -quality switch is made of copper, which is heavier. If alloys or thin copper pieces, the quality is not as good as copper.
fan shell mould https://www.tangrammould.com/Fan-Shell-Mould.html
Be the first person to like this.